Product Detail G166

GUBAILI G166 Modified Acrylic AB Adhesive (Red/Blue)

GUBAILI G166 modified acrylic red/blue AB adhesive: Part A blue-green, Part B red, 1:1 mix and room-temperature cure, working time 2-5 minutes, initial set 3-10 minutes, shear strength 16-30 MPa, service temperature -60 to 150°C. For high-strength structural bonding of metal, plastic, stone and ceramics.

High Strength

High bond strength for structural joints under heavy loads.

High Viscosity

High consistency that resists run-off, ideal for filling large gaps.

Peel Resistance

Strong peel resistance keeps the bond from separating.

Universal

Universal compatibility with a wide range of substrates.

Product Parameters

Technical Parameters
ParameterSpecification / Value
ColorPart A blue-green, Part B red
Viscosity (25°C)Part A/B each 3000 ~ 6000 cP
Mix Ratio1:1 by weight (some models 10:1)
Working Time (25°C)2 ~ 5 minutes
Initial Set Time3 ~ 10 minutes
Full Cure Time24 hours
Shear Strength16 ~ 30 MPa
Temperature Range-60°C ~ +150°C
Solid Content100%
Shelf Life12 months (stored at 25°C, cool and dark)

Product Details

Product Introduction

Product Overview

GUBAILI modified acrylic AB adhesive, commonly known as red/blue adhesive, is a two-component room-temperature fast-curing acrylic structural adhesive. Part A is blue-green and Part B is red; when mixed, a crosslinking reaction cures the adhesive rapidly at room temperature without heating. Solid content is 100% with no solvent. Part A and B viscosities are controlled at 3000-6000 cP with moderate flow for manual or automated dispensing. The adhesive offers high bond strength and toughness, withstands impact and vibration after curing, and provides high-strength structural bonding between dissimilar materials. Shear strength 16-30 MPa, long-term service temperature -60°C to 150°C.

Industries

Widely used for structural bonding of metals, plastics, stone, wood and ceramics. Suitable for hardware products, auto parts, construction machinery components, crafts, molds and furniture assembly.

Instructions

1. Sand, degrease and dust the bonding surfaces and keep them dry and clean;
2. Mix at a 1:1 weight ratio (some versions 10:1) until uniform, avoiding incomplete mixing that affects curing;
3. At 25°C the working time is only 2-5 minutes; apply and join the parts as soon as possible and align them;
4. Initial set takes 3-10 minutes, after which fixturing can be removed; full cure and maximum strength are reached after 24 hours;
5. Wipe uncured squeeze-out with acetone or anhydrous ethanol.

Precautions

1. Store the two components separately, sealed, at 25°C in a cool, dark place; shelf life 12 months;
2. Follow the mix ratio strictly—deviation causes incomplete cure, tackiness and reduced strength;
3. Work in a ventilated area and wear gloves and goggles to avoid contact with skin and eyes;
4. Do not mix large batches at once to prevent rapid exothermic runaway;
5. Not suitable for long-term immersion in strong acids, alkalis or strong solvents.

FAQ

FAQ
What should I watch out for when mixing AB adhesive?

Dispense according to the stated ratio—do not estimate by eye. Scrape the bottom and edges of the container while mixing until the color is completely uniform with no streaks, avoiding uncured pockets.

Mix only as much as you can use within the working time; a large batch generates heat and shortens pot life. Never thin a thickened mix with fresh adhesive.

What are the cure time and temperature performance of AB adhesives?

At room temperature, initial set typically takes 30–60 minutes and final strength about 24 hours; low temperatures extend these times considerably. If early load-bearing is needed, heat curing can be used, but the ramp rate must be controlled.

Leave margin in long-term service temperature and avoid running close to the upper limit. For high-temperature applications, perform heat-aging validation before volume use.

How do I choose between G168 epoxy AB adhesive and G166 red/blue acrylic adhesive?

G168 is a clear epoxy system with temperature resistance, low odor and high strength, suitable for structural bonding of metals, ceramics, glass and rigid plastics. G166 is a modified acrylic system that cures quickly with good toughness, suitable for fast assembly of magnets, metals and plastics.

Choose G168 for longer working time and higher temperature resistance; choose G166 for fast fixturing and impact resistance. Neither system should replace a production-line adhesive without trial validation.

What applications suit G166 modified acrylic AB adhesive?

Fast curing and tough, it suits rapid structural assembly of magnets, metals and plastics.

Odor is relatively noticeable, so work in a ventilated area; for large gaps, apply in layers or use with filler.

Related Products

More Two-Part AB Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×