Product Detail G168

G168 Clear Epoxy AB Adhesive - High-Temperature, Low-Odor Structural Bonding

GUBAILI G168 is a high-performance clear epoxy AB adhesive with high-temperature resistance, low odor and excellent peel strength. Suitable for structural bonding of metals, ceramics, plastics and more, it cures clear and invisible—ideal for industrial repair and DIY work.

High Strength

High bond strength for structural joints under heavy loads.

Peel Resistance

Strong peel resistance keeps the bond from separating.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Universal

Universal compatibility with a wide range of substrates.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Main ComponentEpoxy resin
ColorClear/colorless to slightly yellow viscous liquid
Viscosity3,000 ~ 5,000 cP
Temperature Resistance-45°C ~ 200°C
Working Time5 minutes
Hardness (Shore D)>= 80
Shear Strength (Steel-Steel)>= 22 MPa

Product Details

Product Introduction

GUBAILI G168 is a two-component, 1:1 clear epoxy AB adhesive engineered for bonding applications that demand high strength, durability and visual quality. The cured bond line is transparent and does not affect the appearance of the bonded parts.

Core Advantages

  • High clarity: the cured adhesive is crystal clear, ideal for appearance-critical work such as crafts and jewelry.
  • High-temperature performance: good heat resistance maintains stable bond strength at elevated temperatures.
  • Low odor and environmentally responsible: the optimized formula has very low odor for a more comfortable, operator-friendly process.
  • Strong bonding: excellent adhesion to metals, ceramics, glass, rigid plastics and wood, with high peel resistance.

Applications

  • Industrial maintenance: bonding, fixing and repairing equipment parts.
  • Electronics and electrical: encapsulation, fixing and insulation protection of components.
  • DIY and crafts: crystal resin work, model making and jewelry assembly.
  • Household repair: repairing broken ceramic, marble and similar items.

Instructions

  • Surface preparation: clean and dry the surfaces, removing oil and dust.
  • Mixing: dispense Part A and Part B at a 1:1 volume or weight ratio and mix thoroughly.
  • Application: apply the mixed adhesive evenly to one or both surfaces and join the parts.
  • Curing: allow to cure at room temperature. Initial set takes about 30-60 minutes; full strength is reached after 24 hours.

Precautions

  • Use in a well-ventilated area.
  • Avoid skin and eye contact. In case of contact, rinse immediately with plenty of water.
  • Keep out of reach of children.

FAQ

FAQ
What should I watch out for when mixing AB adhesive?

Dispense according to the stated ratio—do not estimate by eye. Scrape the bottom and edges of the container while mixing until the color is completely uniform with no streaks, avoiding uncured pockets.

Mix only as much as you can use within the working time; a large batch generates heat and shortens pot life. Never thin a thickened mix with fresh adhesive.

What are the cure time and temperature performance of AB adhesives?

At room temperature, initial set typically takes 30–60 minutes and final strength about 24 hours; low temperatures extend these times considerably. If early load-bearing is needed, heat curing can be used, but the ramp rate must be controlled.

Leave margin in long-term service temperature and avoid running close to the upper limit. For high-temperature applications, perform heat-aging validation before volume use.

How do I choose between G168 epoxy AB adhesive and G166 red/blue acrylic adhesive?

G168 is a clear epoxy system with temperature resistance, low odor and high strength, suitable for structural bonding of metals, ceramics, glass and rigid plastics. G166 is a modified acrylic system that cures quickly with good toughness, suitable for fast assembly of magnets, metals and plastics.

Choose G168 for longer working time and higher temperature resistance; choose G166 for fast fixturing and impact resistance. Neither system should replace a production-line adhesive without trial validation.

What substrates suit G168 clear epoxy AB adhesive?

For structural bonding and potting of metals, ceramics, glass and rigid plastics; it cures clear with low odor and good temperature resistance.

Mix thoroughly at 1:1 and allow 24 hours at room temperature for full cure; for high-temperature, high-humidity environments, run reliability validation first.

Related Products

More Two-Part AB Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×