Product Detail U321

GUBAILI U321 UV Adhesive for Glass and Crystal

GUBAILI U321 UV adhesive for glass and crystal: clear, viscosity 400-600 cP, cures in 10-20 seconds under UV light, shear strength >=16 N/mm². For transparent bonding of glass furniture and crystal crafts with an invisible bond line. 50 ml pack.

High Strength

High bond strength for structural joints under heavy loads.

Fast Curing

Fast curing for higher production efficiency.

Transparent

Clear after cure for appearance-critical applications.

UV Curing

Fast curing under UV light.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity400 ~ 600 cP
ColorClear to pale yellow liquid
Cure Time10 ~ 20 seconds (UV exposure)
Shear Strength (Glass/Crystal)>= 16 N/mm²
UV Energy Required1000 mJ/cm²
SubstratesGlass and crystal products
Shelf Life12 months
StorageCool, dry, dark place
Packaging50 ml

Product Details

Product Introduction

Product Overview

U321 is a UV-curing adhesive designed specifically for glass and crystal. The adhesive is a clear to pale yellow liquid and cures to a transparent, virtually invisible bond line that preserves the clarity and appearance of glass and crystal products. Viscosity 400-600 cP, with balanced wetting and gap-filling properties. It cures rapidly under 365 nm UV light, reaching initial set in 10-20 seconds under standard conditions for high production efficiency. The cured bond line adheres strongly to glass and crystal, with shear strength above 16 N/mm², excellent water and weather resistance, and resistance to yellowing and cracking in long-term use.

Industries

Widely used for bonding glass and crystal products such as glass furniture, crystal crafts, crystal jewelry, glass display cases and glass lighting. Especially suitable for transparent materials where optical clarity is critical.

Instructions

1. The bonding surfaces must be clean and dry, free of oil, dust and water marks;
2. Apply a small amount evenly, join the parts and expel air bubbles to ensure a uniform bond line without voids;
3. Cure with a 365 nm UV lamp at an energy dose of at least 1000 mJ/cm²; adjust exposure time according to bond-line thickness;
4. Handle and process only after full cure; uncured residue can be wiped off with alcohol.

Precautions

1. Avoid direct sunlight and strong UV exposure during storage; keep sealed in a cool, dry, dark place;
2. Wear protective gloves and goggles to avoid contact with skin and eyes;
3. Keep the bond gap small—thicker gaps cure more slowly; 0.1 mm or less is recommended;
4. Not suitable for thick-layer bonding of dark or opaque substrates; areas that light cannot reach will not cure;
5. Shelf life 12 months; do not use expired product.

FAQ

FAQ
What conditions must be controlled when applying UV adhesive?

Substrates must be clean and dry, and the bond line should not be too thick, as this affects through-cure. Set lamp distance, power and time according to the process; moving the lamp slightly during exposure reduces shadowed areas.

For stress-sensitive plastics such as PC, be aware of stress-cracking risk from the adhesive; confirm with a small trial first.

Can UV adhesive cure in areas that light cannot reach?

A pure UV system requires UV exposure to cure; shadowed areas and opaque laminates cannot cure fully.

For such structures, use a dual-cure system, irradiate from a transparent side, or use a primer for local treatment.

How do I choose a UV adhesive, and what is the difference between U321, U322 and U323?

Choose U321 for glass, crystal and handicrafts; U322 for transparent plastics such as acrylic, PC and PS; U323 for glass-to-metal and hardware composite parts.

Confirm that the substrate transmits UV light, and check bond-line thickness and lamp distance. If the metal side is opaque, use a dual-cure system or irradiate from the transparent side after dispensing.

Is U321 suitable for bonding glass and crystal?

Highly transparent and non-yellowing, it suits glass furniture, crystal crafts and transparent decorative parts.

Ensure UV light reaches the bond line, and set exposure time and distance according to the process.

Related Products

More UV-Curing Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×