Product Detail 402

GUBAILI 402 High-Temperature Instant Adhesive

GUBAILI 402 high-temperature instant adhesive: viscosity 100 cP, clear bond line, cure in 3-10 seconds, service temperature -40°C to 135°C. Bonds metals, rubber, plastics and difficult substrates for extreme-temperature assembly. Available in 20 g, 500 g and 1000 g packs.

High Strength

High bond strength for structural joints under heavy loads.

Fast Drying

Fast surface drying to shorten waiting time.

Fast Curing

Fast curing for higher production efficiency.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity100 cP
ColorClear
Gap Fill0.005 in. (0.15 mm)
Cure Time (Steel)3-10 seconds
Shear Strength2,900 psi (20 N/mm²)
Temperature Range-40°C to 135°C
Key PropertiesHigh performance, high-temperature resistance
SubstratesMetals, rubber, plastics, difficult-to-bond substrates
Packaging20 g / 500 g / 1000 g

Product Details

Product Introduction

Product Overview

GUBAILI 402 is a high-performance, high-temperature cyanoacrylate adhesive with a low-viscosity clear formula and fast curing. It is optimized for difficult-to-bond substrates and offers excellent heat resistance, delivering more stable bonds under alternating high and low temperatures—ideal for assembly in demanding high-temperature environments.

Viscosity 100 cP, gap fill 0.005 in. (0.15 mm), cure time on steel 3-10 seconds, steel-to-steel shear strength up to 2,900 psi (20 N/mm²), long-term service temperature -40°C to 135°C. The clear bond line is virtually invisible and preserves the appearance of the parts.

Substrates

Metals, rubber, standard plastics and various difficult-to-bond substrates.

Applications

For assembly processes that must maintain high performance under extreme temperatures. Widely used for fast bonding and fixing of electromechanical components, sensor assemblies, rubber and plastic parts, and high-temperature components.

Instructions

1. The bonding surfaces must be clean and dry, free of oil, dust and mold release. Abrading the surface can further improve bond strength.

2. Apply a thin bead only—no thick layer is needed. Join the parts, apply light pressure and hold for 3-10 seconds for initial fixturing; maximum strength is reached after 24 hours.

3. Ambient humidity affects cure speed: curing is slower in dry conditions and faster in high humidity.

Precautions

1. This product cures extremely fast and bonds skin and eyes instantly. Always wear protective gloves and avoid direct contact. If skin is bonded, do not pull it apart—soak in warm water and separate slowly. If adhesive gets into the eyes, flush continuously with plenty of water and seek medical attention promptly.

2. Storage: keep sealed, away from light, in a cool, dry place, away from heat and open flame. Do not store with alkaline substances or amine accelerators.

3. Not suitable for filling large gaps, long-term water immersion, or structural bonding under continuous heavy impact loads.

Packaging: 20 g / 500 g / 1000 g

FAQ

FAQ
How should surfaces be prepared before instant adhesive bonding, and how much adhesive should be applied?

Surfaces must be dry, free of oil, mold release and dust. Metal parts can be wiped with solvent and allowed to flash off completely; low-surface-energy plastics need a primer, otherwise false bonding is likely.

Apply a thin, even bead—enough to form a continuous film after clamping. Excess adhesive slows curing and increases blooming and squeeze-out. Seal porous materials before applying adhesive.

How long does instant adhesive take to cure, and how do I separate a misaligned bond?

Fixturing usually takes seconds to tens of seconds, while final strength requires about 24 hours. Low temperature, large gaps or excess adhesive significantly slow the process.

To separate the parts, use a dedicated debonder or acetone allowed to wick along the bond line. Heat accelerates breakdown but may affect appearance parts. After separation, remove all residue before re-bonding.

How do I choose within the instant adhesive range? What is the difference between 401, 402, 403 and the low-viscosity grades?

For general bonding, choose 401; for high temperature or near heat-generating components, choose 402; for appearance parts, transparent parts and low-odor requirements, choose 403 or 460; for penetrating tiny gaps in assembled parts, choose low-viscosity grades such as 406 or B495/B496.

Where impact resistance, peel resistance or small-gap filling is needed, prefer the toughened B480. First establish direction by substrate and operating conditions, then confirm cure speed and strength with actual test parts.

What applications suit the temperature performance of 402?

A high-temperature instant adhesive for joints near heat-generating components, close to electronic soldering, or in higher ambient temperatures.

Long-term temperature should stay within the grade's upper limit; for continuous high temperature, consider a structural adhesive with higher heat resistance.

Related Products

More Instant Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×