Product Detail 403

GUBAILI 403 Low-Blooming, Low-Odor Instant Adhesive

GUBAILI 403 instant adhesive: high viscosity, low blooming and low odor, pale yellow/clear, viscosity 1200 cP, gap fill 0.24 mm, cure in 30 seconds, service temperature -40°C to 80°C. Suitable for metals, plastics, elastomers and porous materials such as wood, paper, leather and fabric. 20 g/500 g/1000 g packs.

High Viscosity

High consistency that resists run-off, ideal for filling large gaps.

Fast Curing

Fast curing for higher production efficiency.

Low Blooming

Minimal blooming after cure keeps surfaces clean.

Low Odor

Low odor for a more comfortable working environment.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity1200 cP
ColorPale yellow/clear
Gap Fill0.008 in. (0.24 mm)
Cure Time (Steel)30 seconds
Shear Strength2,950 psi (20.3 N/mm²)
Temperature Range-40°C to 80°C (-40°F to 175°F)
Key PropertiesLow blooming, low odor, high viscosity
SubstratesMetals, plastics and elastomers
Packaging20 g / 500 g / 1000 g

Product Details

Product Introduction

Product Overview

GUBAILI 403 is a high-viscosity, low-blooming, low-odor cyanoacrylate adhesive. The adhesive is pale yellow or clear and, compared with standard instant adhesives, produces far less blooming and has a milder odor—ideal for parts with high appearance requirements. Viscosity 1200 cP, gap fill up to 0.008 in. (0.24 mm), cure time on steel 30 seconds, steel-to-steel shear strength up to 2,950 psi (20.3 N/mm²), service temperature -40°C to 80°C (-40°F to 175°F).

Substrates

Metals, plastics and elastomers, including porous and absorbent substrates.

Applications

For fast bonding of most metals, plastics and elastic materials, especially porous or absorbent materials such as wood, paper, leather and fabric. Widely used in crafts, leather goods, textiles and plastic housings where adhesive marks and odor are a concern.

Instructions

1. The bonding surfaces must be clean and dry, free of oil, dust and mold release. For porous substrates, control the amount applied to avoid excessive penetration.

2. Apply a thin, even bead, join the parts and hold under pressure for 30 seconds for initial set; final strength is reached after 24 hours.

3. Ambient humidity affects cure speed. Very high humidity can still cause slight blooming; good ventilation further reduces the risk.

Precautions

1. Fast curing—avoid direct contact with skin and eyes. Wear protective gloves. Do not pull bonded skin apart; soak in warm water and separate slowly. If adhesive gets into the eyes, flush immediately with plenty of water and seek medical attention.

2. Store sealed, away from light, in a cool, dry place, away from heat and open flame. Do not store with amine accelerators or alkaline materials.

3. Not suitable for long-term water immersion, continuous high temperature, or structural parts under heavy impact.

Packaging: 20 g / 500 g / 1000 g

FAQ

FAQ
How should surfaces be prepared before instant adhesive bonding, and how much adhesive should be applied?

Surfaces must be dry, free of oil, mold release and dust. Metal parts can be wiped with solvent and allowed to flash off completely; low-surface-energy plastics need a primer, otherwise false bonding is likely.

Apply a thin, even bead—enough to form a continuous film after clamping. Excess adhesive slows curing and increases blooming and squeeze-out. Seal porous materials before applying adhesive.

How long does instant adhesive take to cure, and how do I separate a misaligned bond?

Fixturing usually takes seconds to tens of seconds, while final strength requires about 24 hours. Low temperature, large gaps or excess adhesive significantly slow the process.

To separate the parts, use a dedicated debonder or acetone allowed to wick along the bond line. Heat accelerates breakdown but may affect appearance parts. After separation, remove all residue before re-bonding.

How do I choose within the instant adhesive range? What is the difference between 401, 402, 403 and the low-viscosity grades?

For general bonding, choose 401; for high temperature or near heat-generating components, choose 402; for appearance parts, transparent parts and low-odor requirements, choose 403 or 460; for penetrating tiny gaps in assembled parts, choose low-viscosity grades such as 406 or B495/B496.

Where impact resistance, peel resistance or small-gap filling is needed, prefer the toughened B480. First establish direction by substrate and operating conditions, then confirm cure speed and strength with actual test parts.

What products is 403, with low blooming and low odor, suited to?

It suits appearance parts, transparent parts, cosmetic packaging and optical components—applications sensitive to blooming and odor.

Maintain ventilation and control the amount applied; excess adhesive can still cause surface hazing. Avoid wiping the bond line immediately after assembly.

Related Products

More Instant Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×