GUBAILI 406 instant adhesive: ultra-low viscosity and high flow, clear, viscosity 20 cP, gap fill 0.12 mm, cure in 30 seconds, service temperature -40°C to 121°C. For fast bonding of plastics, rubber and EPDM. Available in 20 g/500 g/1000 g packs.
High bond strength for structural joints under heavy loads.
Excellent flow and penetration for bonding tight gaps.
Fast surface drying to shorten waiting time.
Fixtures and cures within seconds for instant bonding.
| Parameter | Specification / Value |
|---|---|
| Viscosity | 20 cP |
| Color | Clear |
| Gap Fill | 0.004 in. (0.12 mm) |
| Cure Time (Steel) | 30 seconds |
| Shear Strength | 2,250 psi (15.5 N/mm²) |
| Temperature Range | -40°C to 121°C |
| Key Properties | Ultra-low viscosity, high flow |
| Substrates | Plastics, rubber |
| Packaging | 20 g / 500 g / 1000 g |
Product Overview
GUBAILI 406 is an ultra-low-viscosity cyanoacrylate adhesive with a clear liquid and excellent flow that quickly wets fine gaps. Viscosity 20 cP, gap fill 0.004 in. (0.12 mm), cure time on steel 30 seconds, steel-to-steel shear strength up to 2,250 psi (15.5 N/mm²), long-term service temperature -40°C to 121°C. Its high flow suits capillary penetration into tiny gaps and gives excellent affinity for plastics and rubber.
Substrates
Plastics and rubber, including EPDM and various elastomers.
Applications
Specifically for fast bonding of plastics and rubber, including EPDM and other elastomers. Widely used for rubber and plastic fittings, seals and small plastic parts.
Instructions
1. Clean and dry the bonding surfaces, removing oil, mold release and dust. Because flow is extremely high, control the amount applied to prevent adhesive from running onto non-bonded areas.
2. Apply a small amount, join and press the parts, and hold for 30 seconds for initial fixturing; maximum strength is reached after 24 hours.
3. Ambient humidity affects cure speed—higher humidity cures faster. Manage the amount applied to prevent blooming from squeeze-out.
Precautions
1. Fast curing—wear protective gloves and avoid contact with skin and eyes. Do not pull bonded skin apart; soak in warm water and separate slowly. If adhesive gets into the eyes, flush immediately with plenty of water and seek medical attention.
2. Store sealed, away from light, in a cool place, away from heat and open flame. Do not store with amine accelerators or alkaline materials.
3. Not suitable for large-gap filling, long-term water immersion, or structural bonding under continuous heavy impact.
Packaging: 20 g / 500 g / 1000 g
Surfaces must be dry, free of oil, mold release and dust. Metal parts can be wiped with solvent and allowed to flash off completely; low-surface-energy plastics need a primer, otherwise false bonding is likely.
Apply a thin, even bead—enough to form a continuous film after clamping. Excess adhesive slows curing and increases blooming and squeeze-out. Seal porous materials before applying adhesive.
Fixturing usually takes seconds to tens of seconds, while final strength requires about 24 hours. Low temperature, large gaps or excess adhesive significantly slow the process.
To separate the parts, use a dedicated debonder or acetone allowed to wick along the bond line. Heat accelerates breakdown but may affect appearance parts. After separation, remove all residue before re-bonding.
For general bonding, choose 401; for high temperature or near heat-generating components, choose 402; for appearance parts, transparent parts and low-odor requirements, choose 403 or 460; for penetrating tiny gaps in assembled parts, choose low-viscosity grades such as 406 or B495/B496.
Where impact resistance, peel resistance or small-gap filling is needed, prefer the toughened B480. First establish direction by substrate and operating conditions, then confirm cure speed and strength with actual test parts.
Its very low viscosity makes it ideal for capillary penetration into tiny gaps in assembled parts, as well as for fast fixturing of small areas.
After dispensing, prevent adhesive from running onto non-bonded surfaces; on vertical surfaces, control the amount and have absorbent material ready.
We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.
Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.