Product Detail B222

GUBAILI B222 Low-Strength Removable Threadlocker

GUBAILI B222 purple threadlocker: medium viscosity, low strength, hand-removable, suitable for soft metals such as aluminum and brass, for locking set screws and adjusting screws. Service temperature -55 to 150°C. 50 ml/250 ml available.

Low Strength

Low strength for easy disassembly and rework.

Medium Viscosity

Balanced flow for both penetration and gap filling.

Thixotropic

Non-sagging at rest, flows under shear for easy application.

Removable

Removable for easy maintenance.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity1200 cP
ColorPurple
Thread SizeM8
Initial Set Time20 min
Breakaway Torque6 N·m (50 lb.in)
Average Removal Torque14 N·m (120 lb.in)
Temperature Range-55°C ~ 150°C
StrengthLow strength, hand-removable
Packaging50 ml / 250 ml

Product Details

Product Introduction

Product Overview

GUBAILI B222 is a purple general-purpose anaerobic threadlocker with medium viscosity and low strength, removable with ordinary hand tools. It cures in the absence of air within metal thread clearances, effectively preventing fasteners from loosening or leaking under vibration and impact. It is suitable for softer, low-strength metals such as aluminum and brass that are prone to breakage during disassembly, protecting the substrate from damage.

Industries

Widely used in automation equipment, instruments, controllers and transmission mechanisms, typically for locking and securing collars, pulleys, tool holders, set screws and countersunk adjusting screws.

Instructions

1. Clean oil and dust from the threads and keep the substrate dry and clean;
2. Apply adhesive evenly at the thread engagement area and assemble/tighten into position;
3. Initial set takes about 20 minutes at room temperature; full cure is recommended at 24 hours;
4. For later maintenance, disassemble directly with standard hand tools.

Precautions

1. This is an anaerobic adhesive that cures only in confined metal gaps; it will not cure in open air;
2. Keep away from children and avoid contact with skin and eyes; work in a ventilated area;
3. Not suitable for threadlocking plastics, rubber or other non-metallic threads;
4. Store in a cool, dark place and avoid high temperature and direct sunlight.

FAQ

FAQ
How should threads be prepared before applying threadlocker?

Threads should be degreased, derusted and dry. For blind holes, control the amount of adhesive so it is not forced to the bottom and trapped as a hydraulic lock; for through holes, apply adhesive around the full circumference of the external thread.

Apply adhesive to the engagement area, not the bolt tip, and tighten to torque specification after assembly. Do not let adhesive enter bearings, oil passages or moving joints.

How long does threadlocker take to cure, and how is it disassembled?

Anaerobic adhesives cure when isolated from air and in contact with metal. Initial set typically takes 10–30 minutes and final strength about 24 hours; low temperatures extend these times.

Low- and medium-strength joints can be disassembled with tools. For high-strength joints, heat to about 250°C and disassemble while hot to avoid twisting off the bolt.

How do I choose a threadlocker by strength, and where are 222, 243 and 263 used?

For small screws that are frequently adjusted or serviced, choose low-strength B222, removable with hand tools; for general machinery assembly, choose medium-strength B243; for heavy-duty joints that are rarely disassembled, choose high-strength B263.

For high-temperature applications choose B272; for bolts above M25 choose B277; for reinforcing already-assembled bolts choose penetrating grade B290. The higher the strength, the more disassembly depends on heat or special tools.

Where is low-strength removable B222 used?

For small screws, dowel pins and adjusting bolts that need frequent adjustment or maintenance.

Its low strength is not suitable for heavy loads or high anti-loosening requirements; it can be removed with hand tools after assembly.

Related Products

More Threadlockers Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×