Product Detail B243

GUBAILI B243 Medium-Strength Threadlocker

GUBAILI B243 blue threadlocker: medium viscosity and strength, no primer required, tool-removable, tolerates light oil contamination, suitable for stainless steel, aluminum and plated substrates. Service temperature -55 to 180°C. 50 ml/250 ml available.

Medium Strength

Moderate strength balancing reliability with easy disassembly.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Universal

Universal compatibility with a wide range of substrates.

Removable

Removable for easy maintenance.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity2150 cP
ColorBlue
Thread SizeM30 and below
Initial Set Time10 min
Breakaway Torque26 N·m (230 lb.in)
Average Removal Torque5 N·m (40 lb.in)
Temperature Range-55°C ~ 180°C
StrengthMedium strength, tool-removable
FeaturesNo primer required, tolerates light industrial oil contamination
Packaging50 ml / 250 ml

Product Details

Product Introduction

Product Overview

GUBAILI B243 is a blue general-purpose anaerobic threadlocker with medium viscosity and medium strength. It requires no primer and can be removed with standard tools. It cures in the absence of air within metal thread clearances, locking and sealing threads against loosening caused by equipment vibration. It tolerates light oil contamination—such as small amounts of engine oil, rust-preventive oil or machining fluid—and is compatible with stainless steel, aluminum, plated parts and other metals.

Industries

Widely used for bolt locking and sealing in pumps, motors, gearboxes, presses and other industrial equipment, and for anti-loosening of metal threaded assemblies up to M30.

Instructions

1. Clean oil and contaminants from the threads first; the product can still be used with light oil contamination;
2. Apply adhesive evenly at the thread engagement area and assemble/tighten quickly into position;
3. Initial set takes about 10 minutes at room temperature; full cure strength is reached after 24 hours;
4. For maintenance disassembly, standard tools can be used, with heat assistance if necessary.

Precautions

1. An anaerobic adhesive that cures only in confined metal gaps; it will not cure in open air;
2. Work in a ventilated area and avoid contact with skin and eyes;
3. Not suitable for plastic, rubber or other non-metallic threads;
4. Store in a cool, dark place, away from heat and high temperature.

FAQ

FAQ
How should threads be prepared before applying threadlocker?

Threads should be degreased, derusted and dry. For blind holes, control the amount of adhesive so it is not forced to the bottom and trapped as a hydraulic lock; for through holes, apply adhesive around the full circumference of the external thread.

Apply adhesive to the engagement area, not the bolt tip, and tighten to torque specification after assembly. Do not let adhesive enter bearings, oil passages or moving joints.

How long does threadlocker take to cure, and how is it disassembled?

Anaerobic adhesives cure when isolated from air and in contact with metal. Initial set typically takes 10–30 minutes and final strength about 24 hours; low temperatures extend these times.

Low- and medium-strength joints can be disassembled with tools. For high-strength joints, heat to about 250°C and disassemble while hot to avoid twisting off the bolt.

How do I choose a threadlocker by strength, and where are 222, 243 and 263 used?

For small screws that are frequently adjusted or serviced, choose low-strength B222, removable with hand tools; for general machinery assembly, choose medium-strength B243; for heavy-duty joints that are rarely disassembled, choose high-strength B263.

For high-temperature applications choose B272; for bolts above M25 choose B277; for reinforcing already-assembled bolts choose penetrating grade B290. The higher the strength, the more disassembly depends on heat or special tools.

What connections suit medium-strength B243 threadlocker?

For anti-loosening and sealing of general machinery bolts such as pump bodies, gearboxes and motor end covers.

It can be removed with standard tools; for reassembly, clean off residual adhesive and reapply.

Related Products

More Threadlockers Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×