Product Detail B263

GUBAILI B263 High-Strength Permanent Threadlocker

GUBAILI B263 red high-strength threadlocker: low viscosity, high temperature resistance, suitable for stainless steel, aluminum alloy and plated substrates, for permanent heavy-duty threadlocking. Requires heat for disassembly. Service temperature -55 to 180°C. 50 ml/250 ml available.

High Strength

High bond strength for structural joints under heavy loads.

Low Viscosity

Excellent flow and penetration for bonding tight gaps.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Permanent Locking

Permanent locking for non-removable joints.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity500 cP
ColorRed
Thread SizeM25 and below
Initial Set Time10 min
Breakaway Torque33 N·m (290 lb.in)
Average Removal Torque33 N·m (290 lb.in)
Temperature Range-55°C ~ 180°C
StrengthHigh strength, permanent locking, localized heat required for disassembly
SubstratesStainless steel, aluminum alloy, plated materials, chrome-free coatings and other passive metals
Packaging50 ml / 250 ml

Product Details

Product Introduction

Product Overview

GUBAILI B263 is a red anaerobic threadlocker with low viscosity, high strength and excellent temperature resistance. It is a permanent threadlocking grade that requires localized heating for disassembly. Compatible with metals including stainless steel, aluminum alloy, plated parts and chrome-free coatings, it cures in confined metal thread clearances to lock and seal fasteners, resisting loosening from vibration and impact in heavy-duty, high-strength applications.

Industries

Typically used for engine compartments, pump housings, motor housing studs and other heavy-duty assemblies, and for permanent locking and sealing of threads up to M25.

Instructions

1. Clean oil and dust from the threads and ensure the surfaces are clean and dry;
2. Apply adhesive evenly at the thread engagement area and assemble/tighten into position;
3. Initial set takes 10 minutes at room temperature; full cure strength is reached after 24 hours;
4. If disassembly is required, heat the threaded area locally before removing.

Precautions

1. Anaerobic adhesive—cures only in confined metal gaps and will not cure in open air;
2. Work in a ventilated area and avoid contact with skin and eyes;
3. Not suitable for plastic, rubber or other non-metallic threads;
4. Store in a cool, dark place, away from heat; never store at high temperature.

FAQ

FAQ
How should threads be prepared before applying threadlocker?

Threads should be degreased, derusted and dry. For blind holes, control the amount of adhesive so it is not forced to the bottom and trapped as a hydraulic lock; for through holes, apply adhesive around the full circumference of the external thread.

Apply adhesive to the engagement area, not the bolt tip, and tighten to torque specification after assembly. Do not let adhesive enter bearings, oil passages or moving joints.

How long does threadlocker take to cure, and how is it disassembled?

Anaerobic adhesives cure when isolated from air and in contact with metal. Initial set typically takes 10–30 minutes and final strength about 24 hours; low temperatures extend these times.

Low- and medium-strength joints can be disassembled with tools. For high-strength joints, heat to about 250°C and disassemble while hot to avoid twisting off the bolt.

How do I choose a threadlocker by strength, and where are 222, 243 and 263 used?

For small screws that are frequently adjusted or serviced, choose low-strength B222, removable with hand tools; for general machinery assembly, choose medium-strength B243; for heavy-duty joints that are rarely disassembled, choose high-strength B263.

For high-temperature applications choose B272; for bolts above M25 choose B277; for reinforcing already-assembled bolts choose penetrating grade B290. The higher the strength, the more disassembly depends on heat or special tools.

How is high-strength permanent B263 disassembled?

For heavy-duty bolts and critical joints that are rarely disassembled, with strong anti-loosening performance.

Heat to about 250°C and work while hot; forcing the bolt may damage the threads.

Related Products

More Threadlockers Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×