Product Detail B272

GUBAILI B272 High-Temperature, High-Strength Threadlocker

GUBAILI B272 orange-red high-strength threadlocker: medium viscosity, service temperature -54 to 232°C, for permanent locking and sealing of large metal fasteners M25 and above. 50 ml/250 ml available.

High Strength

High bond strength for structural joints under heavy loads.

Medium Viscosity

Balanced flow for both penetration and gap filling.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Permanent Locking

Permanent locking for non-removable joints.

Product Parameters

Technical Parameters
ParameterSpecification / Value
ViscosityMedium viscosity
ColorOrange-red
ThixotropicNo
Thread SizeM25 and above
Initial Set Time50 min
Breakaway Torque23 N·m (220 lb.in)
Average Removal Torque25 N·m (220 lb.in)
Temperature Range-54°C ~ 232°C
StrengthHigh strength, permanent locking, high-temperature resistant
Packaging50 ml / 250 ml

Product Details

Product Introduction

Product Overview

GUBAILI B272 is an orange-red anaerobic threadlocker with medium viscosity, high strength and excellent high-temperature performance. It is a permanent threadlocking grade with thixotropic behavior. Compatible with a wide range of metal fasteners, it cures in confined thread clearances to lock and seal threaded fasteners, resisting loosening from vibration and impact—especially suited to permanent locking and sealing of large fasteners.

Industries

For permanent locking and sealing of large metal threaded assemblies in high-temperature equipment, heavy machinery and power equipment, for threads of M25 and above.

Instructions

1. Clean oil and dust from the threads and ensure the surfaces are clean and dry;
2. Apply adhesive evenly at the thread engagement area and assemble/tighten into position;
3. Initial set takes 50 minutes at room temperature; full cure strength is reached after 24 hours;
4. If disassembly is required, heat the threaded area locally before removing.

Precautions

1. Anaerobic adhesive—cures only in confined metal gaps and will not cure in open air;
2. Thixotropic and resistant to run-off, suitable for vertical threads;
3. Work in a ventilated area and avoid contact with skin and eyes;
4. Not suitable for plastic, rubber or other non-metallic threads;
5. Store in a cool, dark place away from heat.

FAQ

FAQ
How should threads be prepared before applying threadlocker?

Threads should be degreased, derusted and dry. For blind holes, control the amount of adhesive so it is not forced to the bottom and trapped as a hydraulic lock; for through holes, apply adhesive around the full circumference of the external thread.

Apply adhesive to the engagement area, not the bolt tip, and tighten to torque specification after assembly. Do not let adhesive enter bearings, oil passages or moving joints.

How long does threadlocker take to cure, and how is it disassembled?

Anaerobic adhesives cure when isolated from air and in contact with metal. Initial set typically takes 10–30 minutes and final strength about 24 hours; low temperatures extend these times.

Low- and medium-strength joints can be disassembled with tools. For high-strength joints, heat to about 250°C and disassemble while hot to avoid twisting off the bolt.

How do I choose a threadlocker by strength, and where are 222, 243 and 263 used?

For small screws that are frequently adjusted or serviced, choose low-strength B222, removable with hand tools; for general machinery assembly, choose medium-strength B243; for heavy-duty joints that are rarely disassembled, choose high-strength B263.

For high-temperature applications choose B272; for bolts above M25 choose B277; for reinforcing already-assembled bolts choose penetrating grade B290. The higher the strength, the more disassembly depends on heat or special tools.

What equipment suits high-temperature B272?

For threadlocking and sealing of high-temperature locations such as engines, exhaust systems and hot-oil lines.

Long-term operating temperature should remain below the data-sheet limit; if exceeded, use mechanical locking or a higher-temperature product.

Related Products

More Threadlockers Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×