Product Detail B290

GUBAILI B290 Penetrating Medium-High-Strength Threadlocker

GUBAILI B290 green penetrating threadlocker: low viscosity 40 cP, capillary penetration allows application to already-assembled threads, medium-high strength, hand-removable. For instrument screws and electrical connectors. 50 ml/250 ml available.

Medium Strength

Moderate strength balancing reliability with easy disassembly.

Low Viscosity

Excellent flow and penetration for bonding tight gaps.

Anti-Loosening

Effectively prevents thread loosening.

Removable

Removable for easy maintenance.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity40 cP
ColorGreen
ThixotropicNo
Thread SizeM6 and below
Initial Set Time20 min
Breakaway Torque10 N·m (90 lb.in)
Average Removal Torque29 N·m (260 lb.in)
Temperature Range-55°C ~ 150°C (-65°F ~ 300°F)
StrengthMedium-high strength, penetrating grade, hand-tool removable
Packaging50 ml / 250 ml

Product Details

Product Introduction

Product Overview

GUBAILI B290 is a green, low-viscosity anaerobic threadlocker with a penetrating formula and medium-high strength, removable with hand tools. Through capillary action, the adhesive wicks into threads that are already engaged, so fasteners do not need to be disassembled before application. It cures in confined metal gaps isolated from air, resisting loosening and leakage caused by vibration and impact. It can also fill tiny pores in welds, castings and powder-metallurgy parts—one product, multiple uses.

Industries

For locking pre-assembled fasteners, commonly used on instrument screws and electrical connector bolts, for threads up to M6. Widely used in instruments, electrical equipment and precision hardware assembly.

Instructions

1. Clean dust and oil from the thread surface and keep it dry;
2. Apply adhesive directly to the outside of the assembled threads; it penetrates the thread clearance by capillary action;
3. Initial set takes 20 minutes at room temperature; full cure strength is reached after 24 hours;
4. For later maintenance, disassemble with standard hand tools.

Precautions

1. Anaerobic adhesive—cures only in confined metal gaps and will not cure in open air;
2. Low-viscosity penetrating formula—control the amount applied to avoid overflow;
3. Work in a ventilated area and avoid contact with skin and eyes;
4. Not suitable for plastic, rubber or other non-metallic substrates;
5. Store in a cool, dark place away from heat.

FAQ

FAQ
How should threads be prepared before applying threadlocker?

Threads should be degreased, derusted and dry. For blind holes, control the amount of adhesive so it is not forced to the bottom and trapped as a hydraulic lock; for through holes, apply adhesive around the full circumference of the external thread.

Apply adhesive to the engagement area, not the bolt tip, and tighten to torque specification after assembly. Do not let adhesive enter bearings, oil passages or moving joints.

How long does threadlocker take to cure, and how is it disassembled?

Anaerobic adhesives cure when isolated from air and in contact with metal. Initial set typically takes 10–30 minutes and final strength about 24 hours; low temperatures extend these times.

Low- and medium-strength joints can be disassembled with tools. For high-strength joints, heat to about 250°C and disassemble while hot to avoid twisting off the bolt.

How do I choose a threadlocker by strength, and where are 222, 243 and 263 used?

For small screws that are frequently adjusted or serviced, choose low-strength B222, removable with hand tools; for general machinery assembly, choose medium-strength B243; for heavy-duty joints that are rarely disassembled, choose high-strength B263.

For high-temperature applications choose B272; for bolts above M25 choose B277; for reinforcing already-assembled bolts choose penetrating grade B290. The higher the strength, the more disassembly depends on heat or special tools.

How is penetrating B290 used on already-assembled bolts?

It wicks directly into the threads of assembled joints to reinforce anti-loosening or suppress leakage.

Wipe off excess adhesive after application to avoid contaminating surrounding areas. Performance depends on gap and cleanliness; clean heavily oily parts first.

Related Products

More Threadlockers Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×