Product Detail B603

GUBAILI B603 Cylindrical Retaining Compound

GUBAILI B603 green cylindrical retaining compound: low viscosity, medium strength, for precision fits below 0.1 mm, retaining roller bearings and oil-immersed bushings, preventing loosening and fretting wear. Service temperature -55 to 150°C. 50 ml/250 ml available.

Medium Strength

Moderate strength balancing reliability with easy disassembly.

Low Viscosity

Excellent flow and penetration for bonding tight gaps.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Anti-Loosening

Effectively prevents thread loosening.

Product Parameters

Technical Parameters
ParameterSpecification / Value
ViscosityLow
ColorGreen
ThixotropicNo
Radial Clearance< 0.006 in. / 0.1 mm
Initial Set Time8 min
Compressive Shear Strength (Steel-to-Steel)3260 psi (22.5 N/mm²)
Temperature Range-55°C ~ 150°C (-65°F ~ 300°F)
StrengthMedium strength, resists fretting wear and corrosion
Packaging50 ml / 250 ml

Product Details

Product Introduction

Product Overview

GUBAILI B603 is a green, low-viscosity anaerobic retaining compound with medium strength and no thixotropy. It cures in tightly fitted metal clearances isolated from air, filling the micro-gaps between mating surfaces. It resists loosening and leakage caused by impact and vibration, suppresses fretting wear and galvanic corrosion on the mating surfaces, and improves the coaxiality and load capacity of cylindrical assemblies.

Industries

For precision cylindrical fit assemblies with radial clearance below 0.1 mm, typically retaining roller bearings and oil-immersed bushings in housings. Widely used in reducers, motors and transmission equipment.

Instructions

1. Clean oil, rust and contaminants from the mating surfaces and keep them dry and clean;
2. Apply adhesive evenly to the shaft or bore mating surface and press the parts together quickly into position;
3. Initial set takes 8 minutes at room temperature; maximum cure strength is reached after 24 hours;
4. Ensure sufficient adhesive covers the entire mating area during assembly.

Precautions

1. Anaerobic adhesive—cures only in confined metal gaps and will not cure in open air;
2. Low-viscosity formula—the gap must not be too large; best results are within 0.1 mm;
3. Work in a ventilated area and avoid contact with skin and eyes;
4. Not suitable for plastic, rubber or other non-metallic substrates;
5. Store in a cool, dark place away from heat.

FAQ

FAQ
What should I pay attention to when applying retaining compound?

Degrease and derust both shaft and bore, and keep them dry. Apply adhesive evenly around the circumference of the mating surface, and rotate while pressing in to distribute the adhesive and expel air.

Use enough adhesive that a small bead squeezes out at the joint edge after assembly. Keep adhesive out of bearing races, oil holes and other moving parts, and let the assembly cure undisturbed per the process.

How do retaining compounds perform in terms of temperature and oil resistance?

Standard grades suit general conditions; for long-term high temperature choose B620 or B648; for contact with oil or light oil contamination choose B638 or B648. Refer to the grade data sheet and actual testing for specific temperature ranges.

If the temperature limit is exceeded, switch to a structural adhesive or mechanical reinforcement—do not try to solve it by adding more adhesive.

How do I select a retaining compound by shaft-to-hub clearance?

For small clearances and fast press fits, choose low-viscosity B609; for general shaft-to-hub fits, choose B603; for worn or oversized clearances, choose B680 with greater gap-filling capability.

For assemblies requiring periodic maintenance or disassembly, choose B641; for high-temperature or oily environments, prefer B620, B638 and B648 respectively. Measure actual clearance and coaxiality before selection.

What shaft-to-hub fits suit B603?

A general-purpose retaining compound for conventional retention of bearings, bushings, gears and shafts.

Measure clearance before assembly, and rotate while pressing in to ensure an even adhesive layer.

Related Products

More Retaining Compounds Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×