Product Detail B609

GUBAILI B609 Low-Viscosity Press-Fit Retaining Compound

GUBAILI B609 green cylindrical retaining compound: low viscosity 120 cP, medium-strength press-fit grade, for precision clearances within 0.1 mm, retaining fractional-horsepower motor rotor shafts and bushings, resisting fretting corrosion. Service temperature -54 to 150°C. 50 ml/250 ml available.

Medium Strength

Moderate strength balancing reliability with easy disassembly.

Low Viscosity

Excellent flow and penetration for bonding tight gaps.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Anti-Loosening

Effectively prevents thread loosening.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity120 cP
ColorGreen
ThixotropicNo
Radial Clearance< 0.006 in. / 0.1 mm
Initial Set Time10 min
Compressive Shear Strength (Steel-to-Steel)2300 psi (15 N/mm²)
Temperature Range-54°C ~ 150°C (-65°F ~ 300°F)
Key PropertiesPress-fit, low viscosity, medium strength
Packaging50 ml / 250 ml

Product Details

Product Introduction

Product Overview

GUBAILI B609 is a green, low-viscosity anaerobic retaining compound designed for cylindrical press-fit assemblies, with medium strength and no thixotropy. This one-component anaerobic formula cures only in tightly fitted metal clearances isolated from air. It fills the micro-gaps between shaft and sleeve or bushing and housing, converting discrete contact points into full-surface bonding and greatly improving the load capacity of press-fit assemblies while offsetting the risk of loosening caused by assembly clearance. It blocks moisture and oil, suppresses fretting wear and galvanic corrosion at the interface, improves vibration and impact resistance of precision press fits, compensates for the limitations of mechanical interference fits, and reduces machining tolerance requirements. Its low viscosity provides good flow and evenly wets the entire mating surface for smooth assembly.

Industries

Widely used in micro motors, fractional-horsepower motors, small reducers and precision transmission components. Typically used for retaining fractional and sub-fractional horsepower motor rotor shafts, and for locking bushings and sleeves between shaft and housing. Suitable for precision cylindrical press fits with radial clearance below 0.1 mm.

Instructions

1. Thoroughly clean oil, machining fluid, rust and dust from the shaft and sleeve mating surfaces and dry them;
2. Apply adhesive evenly to the shaft or bore and press the parts together quickly into position;
3. Initial set takes 10 minutes at room temperature; maximum cure strength is reached after 24 hours;
4. Keep the fit clearance within 0.1 mm; excessive clearance reduces cured strength.

Precautions

1. Anaerobic curing depends on oxygen-free confined metal gaps and will not occur in open air;
2. Low-viscosity formula—control the amount applied to avoid excessive squeeze-out onto surrounding parts;
3. Work in a ventilated area and wear protective equipment to avoid contact with skin and eyes;
4. Not suitable for plastic, rubber or other non-metallic substrates;
5. Store sealed in a cool, dark place away from heat and direct sunlight.

FAQ

FAQ
What should I pay attention to when applying retaining compound?

Degrease and derust both shaft and bore, and keep them dry. Apply adhesive evenly around the circumference of the mating surface, and rotate while pressing in to distribute the adhesive and expel air.

Use enough adhesive that a small bead squeezes out at the joint edge after assembly. Keep adhesive out of bearing races, oil holes and other moving parts, and let the assembly cure undisturbed per the process.

How do retaining compounds perform in terms of temperature and oil resistance?

Standard grades suit general conditions; for long-term high temperature choose B620 or B648; for contact with oil or light oil contamination choose B638 or B648. Refer to the grade data sheet and actual testing for specific temperature ranges.

If the temperature limit is exceeded, switch to a structural adhesive or mechanical reinforcement—do not try to solve it by adding more adhesive.

How do I select a retaining compound by shaft-to-hub clearance?

For small clearances and fast press fits, choose low-viscosity B609; for general shaft-to-hub fits, choose B603; for worn or oversized clearances, choose B680 with greater gap-filling capability.

For assemblies requiring periodic maintenance or disassembly, choose B641; for high-temperature or oily environments, prefer B620, B638 and B648 respectively. Measure actual clearance and coaxiality before selection.

How is low-viscosity press-fit B609 applied?

For small-clearance, fast press-fit shaft-to-hub structures; its good flow makes rapid assembly easy.

Match press-fit speed to the adhesive working time to prevent it being displaced prematurely.

Related Products

More Retaining Compounds Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×