GUBAILI B620 green retaining compound: viscosity 8000 cP, medium-high strength and high-temperature resistance, suitable for clearances within 0.2 mm, preventing fretting wear, corrosion and leakage in cylindrical parts. Service temperature -54 to 230°C. 50 ml/250 ml available.
| Parameter | Specification / Value |
|---|---|
| Viscosity | 8000 cP |
| Color | Green |
| Thixotropic | No |
| Radial Clearance | < 0.01 in. / 0.2 mm |
| Initial Set Time | 60 min |
| Compressive Shear Strength (Steel-to-Steel) | 3800 psi (26 N/mm²) |
| Temperature Range | -54°C ~ 230°C (-65°F ~ 450°F) |
| Key Properties | High-temperature resistant, medium viscosity, medium-high strength |
| Packaging | 50 ml / 250 ml |
Product Overview
GUBAILI B620 is a green, medium-viscosity anaerobic retaining compound with medium-high strength and excellent high-temperature performance, with no thixotropy. This one-component anaerobic retaining product cures only in confined metal clearances isolated from air and is suitable for cylindrical fit assemblies with clearance of 0.2 mm or less. After curing, it fills the fine clearance between shaft and bore, converting line and point contact of an interference fit into continuous surface bonding and greatly improving torque transmission. It blocks moisture and media from the interface, suppresses fretting wear and galvanic corrosion during long-term operation, and provides a sealing function, improving assembly stability and service life at high temperatures. Its higher viscosity resists run-off, making it suitable for vertical and inclined cylindrical parts.
Industries
Widely used for retaining cylindrical press-fit components such as motors, reducers, drive wheels, bushings, sleeves and bearings in high-temperature conditions. Suitable for machinery exposed to continuous high temperature, solving loosening, leakage and wear corrosion of cylindrical fits under high-temperature vibration.
Instructions
1. Thoroughly clean oil, machining fluid, rust and dust from the shaft and bore mating surfaces and keep them dry and clean;
2. Apply adhesive evenly to the shaft or bore wall and press the parts together quickly into position;
3. Initial set takes 60 minutes at room temperature; final cure strength is reached after 24 hours;
4. Keep radial fit clearance within 0.2 mm; excessive clearance reduces bond strength.
Precautions
1. Anaerobic adhesive cures in oxygen-free metal gaps and will not cure when exposed to air;
2. Medium-high viscosity formula—adjust the amount applied according to the assembly method;
3. Work in a ventilated area, avoid contact with skin and eyes, and wear protective equipment;
4. Not suitable for retaining plastic, rubber or other non-metallic substrates;
5. Store sealed in a cool, dark place away from heat and direct sunlight.
Degrease and derust both shaft and bore, and keep them dry. Apply adhesive evenly around the circumference of the mating surface, and rotate while pressing in to distribute the adhesive and expel air.
Use enough adhesive that a small bead squeezes out at the joint edge after assembly. Keep adhesive out of bearing races, oil holes and other moving parts, and let the assembly cure undisturbed per the process.
Standard grades suit general conditions; for long-term high temperature choose B620 or B648; for contact with oil or light oil contamination choose B638 or B648. Refer to the grade data sheet and actual testing for specific temperature ranges.
If the temperature limit is exceeded, switch to a structural adhesive or mechanical reinforcement—do not try to solve it by adding more adhesive.
For small clearances and fast press fits, choose low-viscosity B609; for general shaft-to-hub fits, choose B603; for worn or oversized clearances, choose B680 with greater gap-filling capability.
For assemblies requiring periodic maintenance or disassembly, choose B641; for high-temperature or oily environments, prefer B620, B638 and B648 respectively. Measure actual clearance and coaxiality before selection.
For shaft-to-hub retention in high-temperature conditions, such as bearings and bushings near heat sources.
Leave margin in long-term temperature; if exceeded, consider a structural adhesive with higher heat resistance.
We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.
Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.