GUBAILI B648 green retaining compound: viscosity 500 cP, high strength and light oil tolerance, suitable for clearances within 0.15 mm, for clearance and interference fit cylindrical parts, long-term service temperature up to 180°C. 50 ml/250 ml available.
High bond strength for structural joints under heavy loads.
Excellent flow and penetration for bonding tight gaps.
Stable performance over a wide temperature range.
Effectively prevents thread loosening.
| Parameter | Specification / Value |
|---|---|
| Viscosity | 500 cP |
| Color | Green |
| Thixotropic | No |
| Radial Clearance | < 0.006 in. / 0.15 mm |
| Initial Set Time | 3 min |
| Compressive Shear Strength (Steel-to-Steel) | 4480 psi (31 N/mm²) |
| Temperature Range | -54°C ~ 180°C (-65°F ~ 355°F) |
| Key Properties | High-temperature resistant, low viscosity, high strength, light oil tolerant |
| Packaging | 50 ml / 250 ml |
Product Overview
GUBAILI B648 is a green, low-viscosity anaerobic retaining compound with a high-strength formula, high-temperature resistance and tolerance for light oil contamination, with no thixotropy. This one-component anaerobic system cures only in confined metal clearances isolated from air and suits cylindrical fit assemblies with radial clearance below 0.15 mm, providing reliable retention for both clearance and interference fits. The cured bond line fills the fine gap between shaft and bore, converting localized point contact into continuous surface bonding, significantly improving torque transmission and suppressing fretting wear and loosening during long-term operation. Its outstanding high-temperature performance allows stable operation at 180°C, and it tolerates small amounts of machining fluid or oil on the parts, reducing strict degreasing requirements and supporting fast production-line assembly.
Industries
Widely used for retaining motors, reducers, high-temperature transmission components, bearings and bushings. Suitable for locking clearance and interference fit parts that operate continuously at high temperature with clearance within 0.15 mm.
Instructions
1. Remove heavy oil, rust and dust from the mating surfaces where possible; light oil contamination does not affect curing;
2. Apply adhesive evenly to the shaft or bore wall and press the parts together quickly into position;
3. Initial set takes 3 minutes at room temperature; final cure strength is reached after 24 hours;
4. Keep radial clearance within 0.15 mm; excessive clearance significantly reduces bond strength.
Precautions
1. Anaerobic adhesive cures only in oxygen-free confined metal gaps and will not cure when exposed to air;
2. Tolerates only light oil contamination—heavy grease must be removed beforehand;
3. Work in a ventilated area, avoid contact with skin and eyes, and wear protective equipment;
4. Not suitable for retaining plastic, rubber or other non-metallic substrates;
5. Store sealed in a cool, dark place away from heat and direct sunlight.
Degrease and derust both shaft and bore, and keep them dry. Apply adhesive evenly around the circumference of the mating surface, and rotate while pressing in to distribute the adhesive and expel air.
Use enough adhesive that a small bead squeezes out at the joint edge after assembly. Keep adhesive out of bearing races, oil holes and other moving parts, and let the assembly cure undisturbed per the process.
Standard grades suit general conditions; for long-term high temperature choose B620 or B648; for contact with oil or light oil contamination choose B638 or B648. Refer to the grade data sheet and actual testing for specific temperature ranges.
If the temperature limit is exceeded, switch to a structural adhesive or mechanical reinforcement—do not try to solve it by adding more adhesive.
For small clearances and fast press fits, choose low-viscosity B609; for general shaft-to-hub fits, choose B603; for worn or oversized clearances, choose B680 with greater gap-filling capability.
For assemblies requiring periodic maintenance or disassembly, choose B641; for high-temperature or oily environments, prefer B620, B638 and B648 respectively. Measure actual clearance and coaxiality before selection.
For shaft-to-hub retention in engines, gearboxes and other locations exposed to both high temperature and oil.
Clean mating surfaces before assembly; an excessively thick oil film reduces strength.
We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.
Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.