Product Detail B680

GUBAILI B680 Large-Gap High-Strength Retaining Compound

GUBAILI B680 green retaining compound: viscosity 750-1750 cP, high strength, oil and high-temperature resistance, accommodates gaps up to 0.38 mm, for shafts, gears and pulleys under high dynamic loads. Service temperature -54 to 180°C. 50 ml/250 ml available.

High Strength

High bond strength for structural joints under heavy loads.

Medium Viscosity

Balanced flow for both penetration and gap filling.

Oil Solubility

Tolerates oily surfaces with reliable adhesion.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity750 ~ 1750 cP
ColorGreen
ThixotropicNo
Radial Clearance< 0.38 mm
Initial Set Time10 min
Compressive Shear Strength (Steel-to-Steel)4480 psi (31 N/mm²)
Temperature Range-54°C ~ 180°C (-65°F ~ 356°F)
Key PropertiesHigh strength, high-temperature resistant, grease resistant, light contamination tolerant, large-gap capability
Packaging50 ml / 250 ml

Product Details

Product Introduction

Product Overview

GUBAILI B680 is a green anaerobic retaining compound with a viscosity range of 750-1750 cP, high strength, high-temperature resistance and excellent resistance to grease and light contamination, with no thixotropy. It is a one-component anaerobic retaining product developed specifically for large-clearance applications. Curing in confined metal gaps isolated from air, it accommodates radial clearance up to 0.38 mm and is especially suitable for cylindrical fits with clearances around 0.25 mm, overcoming the limited gap range of standard retaining compounds. The cured bond line fully fills larger assembly gaps between shaft and bore, converting discrete point contact into continuous bonding and greatly improving torque transmission. The bond line is tough and can withstand high dynamic and cyclic loads over time, damping vibration and impact, suppressing fretting wear, loosening and media leakage at the interface. Small amounts of oil or contaminants on the parts have little effect on curing, reducing cleaning requirements before assembly.

Industries

Widely used for heavily loaded transmission components, typically for retaining shafts, gears, pulleys and other cylindrical parts. Suitable for reducers, construction machinery and conveying equipment under cyclic loads, and for large-clearance cylindrical fits.

Instructions

1. Remove heavy oil, rust and dust from the mating surfaces where possible; normal use is possible with light contamination;
2. Apply adhesive evenly to the shaft or bore wall and press the parts together quickly into position;
3. Initial set takes 10 minutes at room temperature; final cure strength is reached after 24 hours;
4. Keep radial clearance within 0.38 mm; exceeding this limit significantly reduces cured strength.

Precautions

1. Anaerobic curing occurs in oxygen-free confined metal gaps and will not occur when exposed to air;
2. Tolerates only light oil and contaminants—heavy grease and debris must be removed beforehand;
3. Work in a ventilated area and wear protective equipment to avoid contact with skin and eyes;
4. Not suitable for retaining or bonding plastic, rubber or other non-metallic substrates;
5. Store sealed in a cool, dark place away from heat and direct sunlight.

FAQ

FAQ
What should I pay attention to when applying retaining compound?

Degrease and derust both shaft and bore, and keep them dry. Apply adhesive evenly around the circumference of the mating surface, and rotate while pressing in to distribute the adhesive and expel air.

Use enough adhesive that a small bead squeezes out at the joint edge after assembly. Keep adhesive out of bearing races, oil holes and other moving parts, and let the assembly cure undisturbed per the process.

How do retaining compounds perform in terms of temperature and oil resistance?

Standard grades suit general conditions; for long-term high temperature choose B620 or B648; for contact with oil or light oil contamination choose B638 or B648. Refer to the grade data sheet and actual testing for specific temperature ranges.

If the temperature limit is exceeded, switch to a structural adhesive or mechanical reinforcement—do not try to solve it by adding more adhesive.

How do I select a retaining compound by shaft-to-hub clearance?

For small clearances and fast press fits, choose low-viscosity B609; for general shaft-to-hub fits, choose B603; for worn or oversized clearances, choose B680 with greater gap-filling capability.

For assemblies requiring periodic maintenance or disassembly, choose B641; for high-temperature or oily environments, prefer B620, B638 and B648 respectively. Measure actual clearance and coaxiality before selection.

How is B680 used for large-gap repair?

Its strong gap-filling capability suits repair of worn or out-of-tolerance shaft-to-hub fits, reducing the need for sleeving.

For very large gaps, still evaluate coaxiality and load requirements, and use mechanical reinforcement where necessary.

Related Products

More Retaining Compounds Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×