Product Detail B480

GUBAILI 480 Toughened Black Instant Adhesive

GUBAILI 480 black toughened instant adhesive: viscosity 200 cP, high strength with impact and peel resistance, gap fill 0.18 mm, cure in 90 seconds, service temperature -40°C to 100°C, moisture resistant. For metals, rubber, plastics and magnets in high-peel, high-impact applications. 20 g/500 g/1000 g packs.

High Strength

High bond strength for structural joints under heavy loads.

Medium Viscosity

Balanced flow for both penetration and gap filling.

Fast Drying

Fast surface drying to shorten waiting time.

Fast Curing

Fast curing for higher production efficiency.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity200 cP
ColorBlack
Gap Fill0.006 in. (0.18 mm)
Cure Time (Steel)90 seconds
Shear Strength3,800 psi (26 N/mm²)
Temperature Range-40°C to 100°C (-40°F to 212°F)
Key PropertiesHigh strength, impact resistant, peel resistant
SubstratesMetals, rubber, plastics
Packaging20 g / 500 g / 1000 g

Product Details

Product Introduction

Product Overview

GUBAILI 480 is a toughened, modified black cyanoacrylate adhesive with high strength, impact resistance and peel resistance. Unlike conventional brittle instant adhesives, its bond line has built-in toughness. Viscosity 200 cP, gap fill up to 0.006 in. (0.18 mm), cure time on steel 90 seconds, steel-to-steel shear strength up to 3,800 psi (26 N/mm²), service temperature -40°C to 100°C (-40°F to 212°F). It also offers excellent moisture resistance for bonding in damp conditions.

Substrates

Metals, rubber and plastics, including dissimilar metal-to-magnet assemblies.

Applications

For bonding metal-to-metal, metal-to-rubber and metal-to-magnet joints. The tough bond line and outstanding moisture resistance make it especially suitable for metal bonding in damp environments. Used in assemblies requiring impact and peel strength, such as motor magnets, vibration-damping rubber and plastic components, and hardware fittings.

Instructions

1. Clean and dry the bonding surfaces, removing oil, dust, rust-preventive oil and mold release. Abrading the substrate can further improve peel strength.

2. Apply adhesive evenly, join the parts and hold under pressure for 90 seconds for initial fixturing; maximum strength is reached after 24 hours.

3. Curing is faster in damp environments; control the amount applied to avoid squeeze-out.

Precautions

1. Fast curing—always wear protective gloves and avoid contact with skin and eyes. Never pull bonded skin apart; soak in warm water and separate slowly. If adhesive gets into the eyes, flush immediately with plenty of water and seek medical attention.

2. Store sealed, away from light, in a cool, dry place, away from heat and open flame. Do not store with amine accelerators or alkaline materials.

3. Not suitable for long-term water immersion, continuous high temperature, or filling large gaps.

Packaging: 20 g / 500 g / 1000 g

FAQ

FAQ
How should surfaces be prepared before instant adhesive bonding, and how much adhesive should be applied?

Surfaces must be dry, free of oil, mold release and dust. Metal parts can be wiped with solvent and allowed to flash off completely; low-surface-energy plastics need a primer, otherwise false bonding is likely.

Apply a thin, even bead—enough to form a continuous film after clamping. Excess adhesive slows curing and increases blooming and squeeze-out. Seal porous materials before applying adhesive.

How long does instant adhesive take to cure, and how do I separate a misaligned bond?

Fixturing usually takes seconds to tens of seconds, while final strength requires about 24 hours. Low temperature, large gaps or excess adhesive significantly slow the process.

To separate the parts, use a dedicated debonder or acetone allowed to wick along the bond line. Heat accelerates breakdown but may affect appearance parts. After separation, remove all residue before re-bonding.

How do I choose within the instant adhesive range? What is the difference between 401, 402, 403 and the low-viscosity grades?

For general bonding, choose 401; for high temperature or near heat-generating components, choose 402; for appearance parts, transparent parts and low-odor requirements, choose 403 or 460; for penetrating tiny gaps in assembled parts, choose low-viscosity grades such as 406 or B495/B496.

Where impact resistance, peel resistance or small-gap filling is needed, prefer the toughened B480. First establish direction by substrate and operating conditions, then confirm cure speed and strength with actual test parts.

What bonding is the toughened B480 suitable for?

A toughened black instant adhesive with good impact and peel resistance, suitable for structural fixturing and small-gap filling between metals, plastics and rubber.

The black bond line reduces visibility, but adhesive volume still needs control; for large gaps, use a gap-filling product or structural adhesive.

Related Products

More Instant Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×