GUBAILI B495 general-purpose instant adhesive: clear, low viscosity 40 cP, gap fill 0.12 mm, 5-second initial set, service temperature -40°C to 121°C. For fast bonding of plastics, rubber and metals. 20 g/500 g/1000 g packs.
High bond strength for structural joints under heavy loads.
Excellent flow and penetration for bonding tight gaps.
Fast surface drying to shorten waiting time.
Fast curing for higher production efficiency.
| Parameter | Specification / Value |
|---|---|
| Viscosity | 40 cP |
| Color | Clear |
| Gap Fill | 0.004 in. (0.12 mm) |
| Cure Time (Steel) | 5 seconds |
| Shear Strength | 2,060 psi (14.2 N/mm²) |
| Temperature Range | -40°C to 121°C (-40°F to 250°F) |
| Key Properties | General-purpose, low viscosity |
| Substrates | Plastics, rubber and metals |
| Packaging | 20 g / 500 g / 1000 g |
Product Overview
GUBAILI B495 is a low-viscosity, general-purpose cyanoacrylate adhesive with a clear liquid, good wetting and fast curing, suitable for rapid assembly of many substrates. Viscosity 40 cP, gap fill up to 0.004 in. (0.12 mm), cure time on steel 5 seconds, steel-to-steel shear strength up to 2,060 psi (14.2 N/mm²), service temperature -40°C to 121°C (-40°F to 250°F). Its broad compatibility makes it a highly versatile fast-bonding product.
Substrates
Plastics, rubber and metals.
Applications
A low-viscosity general-purpose instant adhesive for fast bonding of plastics, rubber, metals and other materials. Widely used for rapid assembly and fixing of small plastic, rubber and hardware parts.
Instructions
1. The bonding surfaces must be clean and dry, free of oil, dust and mold release.
2. Apply a small amount, join the parts quickly, and hold under light pressure for 5 seconds for initial fixturing; maximum strength is reached after 24 hours.
3. Viscosity is relatively low and flow is good—control the amount applied to prevent squeeze-out onto the part surface.
Precautions
1. Cures extremely fast and can bond skin and eyes. Wear protective gloves and avoid direct contact. If skin is bonded, do not pull it apart—soak in warm water and separate slowly. If adhesive gets into the eyes, flush immediately with plenty of water and seek medical attention.
2. Store sealed, away from light, in a cool, dry place, away from heat and open flame. Do not store with amine accelerators or alkaline substances.
3. Not suitable for long-term water immersion, structural parts under continuous heavy impact, or large-gap filling.
Packaging: 20 g / 500 g / 1000 g
Surfaces must be dry, free of oil, mold release and dust. Metal parts can be wiped with solvent and allowed to flash off completely; low-surface-energy plastics need a primer, otherwise false bonding is likely.
Apply a thin, even bead—enough to form a continuous film after clamping. Excess adhesive slows curing and increases blooming and squeeze-out. Seal porous materials before applying adhesive.
Fixturing usually takes seconds to tens of seconds, while final strength requires about 24 hours. Low temperature, large gaps or excess adhesive significantly slow the process.
To separate the parts, use a dedicated debonder or acetone allowed to wick along the bond line. Heat accelerates breakdown but may affect appearance parts. After separation, remove all residue before re-bonding.
For general bonding, choose 401; for high temperature or near heat-generating components, choose 402; for appearance parts, transparent parts and low-odor requirements, choose 403 or 460; for penetrating tiny gaps in assembled parts, choose low-viscosity grades such as 406 or B495/B496.
Where impact resistance, peel resistance or small-gap filling is needed, prefer the toughened B480. First establish direction by substrate and operating conditions, then confirm cure speed and strength with actual test parts.
A low-viscosity general-purpose instant adhesive for fast bonding of small gaps and small areas, commonly used in production-line dispensing.
Curing slows when assembly gaps are too large; control fit accuracy or switch to a higher-viscosity grade.
We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.
Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.