Product Detail B496

GUBAILI 496 Low-Viscosity General-Purpose Instant Adhesive

GUBAILI 496 instant adhesive: clear, low viscosity 125 cP, gap fill 0.15 mm, cure in 10-30 seconds, shear strength 2,900-4,350 psi (20-30 N/mm²), service temperature -40°C to +80°C. Primarily for metals, compatible with rubber and plastics. 20 g/500 g/1000 g packs.

High Strength

High bond strength for structural joints under heavy loads.

Low Viscosity

Excellent flow and penetration for bonding tight gaps.

Instant Setting

Fixtures and cures within seconds for instant bonding.

Transparent

Clear after cure for appearance-critical applications.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Viscosity125 cP
ColorClear
Gap Fill0.005 in. (0.15 mm)
Cure Time (Steel)10-30 seconds
Shear Strength2,900-4,350 psi (20-30 N/mm²)
Temperature Range-40°C to +80°C
Key PropertiesGeneral-purpose, low viscosity
SubstratesRubber, plastics, metals, especially metal surfaces
Packaging20 g / 500 g / 1000 g

Product Details

Product Introduction

Product Overview

GUBAILI 496 is a low-viscosity, general-purpose cyanoacrylate adhesive with a clear liquid, good wetting and consistent cure speed. Viscosity 125 cP, gap fill up to 0.005 in. (0.15 mm), cure time on steel 10-30 seconds, steel-to-steel shear strength 2,900-4,350 psi (20-30 N/mm²), long-term service temperature -40°C to +80°C. It performs exceptionally well on metal substrates while remaining compatible with rubber, plastics and other materials—a broadly applicable assembly adhesive.

Substrates

Rubber, plastics and metals, especially metal surfaces.

Applications

A general-purpose instant adhesive optimized for metal bonding, also used for fast assembly and fixing of rubber and plastic parts. Widely used in hardware fittings, rubber and plastic components, and small electromechanical parts.

Instructions

1. Clean and dry the bonding surfaces, removing oil, dust, rust-preventive oil and mold release. Abrading metal substrates can further improve bond strength.

2. Apply a small amount, join and press the parts, and hold for 10-30 seconds for initial fixturing; final strength is reached after 24 hours.

3. Ambient humidity affects cure speed—higher humidity cures faster. Control the amount applied to avoid blooming from squeeze-out.

Precautions

1. Fast curing—wear protective gloves and avoid contact with skin and eyes. Do not pull bonded skin apart; soak in warm water and separate slowly. If adhesive gets into the eyes, flush immediately with plenty of water and seek medical attention.

2. Store sealed, away from light, in a cool, dry place, away from heat and open flame. Do not store with amine accelerators or alkaline materials.

3. Not suitable for long-term water immersion, continuous high temperature, structural parts under heavy impact, or large-gap filling.

Packaging: 20 g / 500 g / 1000 g

FAQ

FAQ
How should surfaces be prepared before instant adhesive bonding, and how much adhesive should be applied?

Surfaces must be dry, free of oil, mold release and dust. Metal parts can be wiped with solvent and allowed to flash off completely; low-surface-energy plastics need a primer, otherwise false bonding is likely.

Apply a thin, even bead—enough to form a continuous film after clamping. Excess adhesive slows curing and increases blooming and squeeze-out. Seal porous materials before applying adhesive.

How long does instant adhesive take to cure, and how do I separate a misaligned bond?

Fixturing usually takes seconds to tens of seconds, while final strength requires about 24 hours. Low temperature, large gaps or excess adhesive significantly slow the process.

To separate the parts, use a dedicated debonder or acetone allowed to wick along the bond line. Heat accelerates breakdown but may affect appearance parts. After separation, remove all residue before re-bonding.

How do I choose within the instant adhesive range? What is the difference between 401, 402, 403 and the low-viscosity grades?

For general bonding, choose 401; for high temperature or near heat-generating components, choose 402; for appearance parts, transparent parts and low-odor requirements, choose 403 or 460; for penetrating tiny gaps in assembled parts, choose low-viscosity grades such as 406 or B495/B496.

Where impact resistance, peel resistance or small-gap filling is needed, prefer the toughened B480. First establish direction by substrate and operating conditions, then confirm cure speed and strength with actual test parts.

How do I choose between B496 and B495?

B496 is also a low-viscosity general-purpose grade for fast fixturing of plastics, metals and rubber, with a quick fixturing speed.

The main differences are cure speed and substrate feel; choose based on line takt time and trial results.

Related Products

More Instant Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×