Product Detail G587

GUBAILI G587 Silicone Gasket Sealant

GUBAILI G587 one-component blue silicone gasket sealant: thixotropic, maximum temperature 260°C, elongation 350%, good insulation. For automotive engine sealing and replacement of pre-cut gaskets and thread tape.

Thixotropic

Non-sagging at rest, flows under shear for easy application.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Flexible

Flexible and elastic after cure, accommodating movement and vibration.

Sealing

Forms a tight seal against gas and liquid leakage.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Product TypeSilicone gasket sealant
Chemical BaseSilicone (organosilicon)
ComponentsOne-component
ColorBlue
ViscosityThixotropic
Specific Gravity1.3
Surface Tack-Free Time30 minutes
Full Cure Time10 ~ 72 hours (varies with environment)
Hardness (Shore A)33 ~ 40
Tensile Strength>= 1.6 MPa
Elongation350%
Maximum Temperature260°C
Dielectric Strength25 kV/mm
Flash Point> 200°F
Mix RatioNo mixing required; one-component ready to use
Recommended SubstratesMetal flanges, metal pipes, engine metal components

Product Details

Product Introduction

Product Overview

GUBAILI G587 is a one-component blue silicone gasket sealant based on silicone rubber. Its thixotropic formula resists run-off on vertical surfaces and requires no mixing. It cures with moisture to form a highly elastic silicone rubber seal with elongation up to 350%, accommodating minor deformation from thermal expansion and contraction without cracking or leaking. It offers outstanding high-temperature resistance up to 260°C and good electrical insulation with a dielectric strength of 25 kV/mm. Commonly used as a formed-in-place gasket (FIPG), it directly replaces conventional pre-cut rubber gaskets and thread seal tape. Widely used for automotive powertrain sealing, industrial flanges and metal piping, it suits both OEM assembly and equipment maintenance.

Industries

Automotive manufacturing and repair: engine valve covers, rocker covers, oil pans, water pumps, intake manifolds, end-face seals and rear axle housing sealing. Also for flat-face sealing of industrial metal flanges and pipes, equipment maintenance and OEM assembly.

Instructions

1. Thoroughly clean the sealing surfaces, removing oil, old adhesive residue and dust, and keep them dry and clean;
2. Apply a continuous, uniform closed-loop bead along the sealing path; the thixotropic formula resists run-off on vertical surfaces;
3. Align and assemble/tighten the parts and allow ambient moisture to cure; surface tack-free in about 30 minutes, full cure 10-72 hours depending on temperature and humidity;
4. Wipe uncured squeeze-out with anhydrous ethanol; cured silicone can be removed mechanically with a blade or sandpaper.

Precautions

1. This is a moisture-curing silicone adhesive; ambient humidity significantly affects cure speed, and low temperature and low humidity greatly extend cure time;
2. Not suitable for long-term immersion in strong solvents, strong acids or alkalis;
3. Work in a ventilated area and wear protective gloves to avoid contact with skin and eyes;
4. Curing releases small molecules; evaluate compatibility before sealing some electronic components;
5. Industrial sealing adhesive—keep away from children and do not ingest.

FAQ

FAQ
How should flange surfaces be prepared before applying sealant?

Degrease, derust and remove old sealant and burrs from the flange face, and keep it dry. Apply a continuous closed bead, keeping clear of the inside of bolt holes and leaving bolt passages open.

After assembly, tighten in stages in a diagonal sequence to the specified torque, avoiding squeezing the sealant out on one side and creating an interruption in the seal.

Are sealants resistant to temperature and oil, and how are they disassembled?

Anaerobic types suit medium-to-high temperature sealing of rigid structures, while silicone types cover a wider temperature range and remain flexible. For oil contact, select an oil-resistant grade based on the media. Refer to the data sheet for specific temperatures.

To disassemble, separate the flange first, then remove residual sealant with a scraper or dedicated cleaner without scratching the sealing face; leftover sealant will impair the next seal.

For flange sealing, should I choose anaerobic or silicone?

For rigid flanges requiring immediate pressure resistance and high temperature performance, prefer anaerobic types such as G510 and G515; for stamped sheet metal, uneven gaps or slightly distorted flanges, choose semi-flexible G518.

For high temperature or a wider temperature range, choose silicone types G596 and G598; for oil contact, prefer G5699; to replace conventional gaskets, choose G587.

Can G587 silicone gasket sealant replace a gasket?

In many cases it can replace conventional pre-cut gaskets, and it suits irregular flange faces and sealing points requiring heat resistance.

Apply as a closed bead; confirm the surface is free of oil and old sealant before assembly.

Related Products

More Structural & Sealant Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×