Product Detail G598

GUBAILI G598 High-Performance Silicone Flat-Face Sealant

GUBAILI G598 one-component black oxime silicone flat-face sealant: low odor and non-corrosive, resistant to engine oil and antifreeze, aging and weather resistant, maximum gap fill 6 mm. For automotive and construction machinery flange sealing. 300 ml.

High Viscosity

High consistency that resists run-off, ideal for filling large gaps.

Thixotropic

Non-sagging at rest, flows under shear for easy application.

High/Low Temp Resistance

Stable performance over a wide temperature range.

Sealing

Forms a tight seal against gas and liquid leakage.

Product Parameters

Technical Parameters
ParameterSpecification / Value
Product TypeSilicone flat-face sealant (RTV silicone rubber)
Chemical BaseSilicone (oxime silicone resin)
Cure MethodOxime-cure room-temperature vulcanization
ComponentsOne-component
ColorBlack (metallic black)
FormPaste, thixotropic
Specific Gravity (@25°C)1.27 ~ 1.32
Hardness (Shore A)A26 ~ A40
Tensile Strength>= 1.31 MPa
Elongation>= 325%
Surface Tack-Free Time<= 25 minutes
Initial Cure Time2 hours
Full Cure Time24 hours (room temperature; optimum performance at 72 hours)
Maximum Gap Fill6 mm
Service Temperature Range-54°C ~ 204°C
Flash Point200°F
Storage8 ~ 21°C, cool and dry
Shelf Life12 ~ 24 months (subject to package label)
Recommended SubstratesCast iron, steel, aluminum and other metal flanges and stamped metal parts
Packaging300 ml

Product Details

Product Introduction

Product Overview

GUBAILI G598 is a high-performance, one-component oxime-cure RTV silicone flat-face sealant. The adhesive is a metallic black paste with built-in thixotropy that resists sagging on vertical surfaces. Its oxime-cure system is low-odor, low-volatility and non-corrosive to substrates, and it is designed for flange sealing in automotive, construction machinery, internal combustion engines and mining equipment. The cured bond line is flexible with outstanding lubricant resistance, tolerating engine oil, transmission fluid and antifreeze. It resists aging, UV and ozone, and does not harden, shrink or become brittle after repeated thermal cycles, ensuring durable sealing. It fills gaps up to 6 mm, compensating for significant flange unevenness and directly replacing conventional preformed solid gaskets. There is an assembly window after application, so the parts must be aligned and pressed within the specified time for proper seal formation.

Industries

Automotive powertrains: oil pans, gearbox housings, valve covers, timing gear covers and differential cover flanges. Flat-face sealing for construction machinery, internal combustion engines and mining machinery. Stamped metal covers, oil pans, timing covers and other stamped metal parts, for OEM assembly and equipment repair.

Instructions

1. Thoroughly clean the sealing surfaces, removing oil, old adhesive residue and dust, and keep them dry and clean;
2. Apply a continuous closed-loop bead along the sealing path, circling around the bolt holes;
3. Assemble and press the parts within 5 minutes of application to ensure the adhesive spreads evenly;
4. Tighten the bolts to standard torque to prevent misalignment; surface tack-free in 25 minutes or less, initial cure in 2 hours, room-temperature cure in 24 hours and optimum sealing performance at 72 hours;
5. Wipe uncured squeeze-out with a non-polar solvent; cured adhesive can be scraped off with a knife.

Precautions

1. Not suitable for continuous direct contact with gasoline; do not use as a cylinder head gasket or cylinder sealant;
2. The adhesive begins curing on contact with air—strictly control the assembly window;
3. Work in a ventilated area and wear protective gloves to avoid contact with skin and eyes;
4. Storage: keep unopened original packaging at 8-21°C in a cool, dry place; shelf life 12-24 months, subject to the package label;
5. Industrial adhesive—keep away from children and do not ingest.

FAQ

FAQ
How should flange surfaces be prepared before applying sealant?

Degrease, derust and remove old sealant and burrs from the flange face, and keep it dry. Apply a continuous closed bead, keeping clear of the inside of bolt holes and leaving bolt passages open.

After assembly, tighten in stages in a diagonal sequence to the specified torque, avoiding squeezing the sealant out on one side and creating an interruption in the seal.

Are sealants resistant to temperature and oil, and how are they disassembled?

Anaerobic types suit medium-to-high temperature sealing of rigid structures, while silicone types cover a wider temperature range and remain flexible. For oil contact, select an oil-resistant grade based on the media. Refer to the data sheet for specific temperatures.

To disassemble, separate the flange first, then remove residual sealant with a scraper or dedicated cleaner without scratching the sealing face; leftover sealant will impair the next seal.

For flange sealing, should I choose anaerobic or silicone?

For rigid flanges requiring immediate pressure resistance and high temperature performance, prefer anaerobic types such as G510 and G515; for stamped sheet metal, uneven gaps or slightly distorted flanges, choose semi-flexible G518.

For high temperature or a wider temperature range, choose silicone types G596 and G598; for oil contact, prefer G5699; to replace conventional gaskets, choose G587.

How do I choose high-performance G598 silicone flat sealant?

For metal flat-face sealing with oil resistance, temperature resistance and good flexibility, accommodating thermal expansion and contraction.

Apply a continuous, even bead and tighten according to the torque sequence after assembly.

Related Products

More Structural & Sealant Adhesives Options

Need a formulation matched to your application?

We customise formulations by substrate, viscosity, cure speed and media resistance, and provide sample testing and technical selection support.

Custom Bonding Solutions

Need adhesive selection advice or sample testing?

Tell us about your application and our engineers will provide product recommendations, sample dispatch and technical support within 48 hours.

×